Browsing Category

Immortan Joe

Cosplay & Props Immortan Joe

Castle Nut Codpiece

By
on
August 21, 2016

Codpiece section is pretty much done. The seams got sewn up, and it was wet-shaped over a bowl to give it a bit more of a curve.

I busted out…

3D Printing Cosplay & Props Immortan Joe

Always wear protection!

By
on
August 19, 2016

We took a bit of time today to give some attention to the codpiece. I think this layout is… close to right? Sorry about the blurry photography.

To get the…

Cosplay & Props Immortan Joe

Building Biceps

By
on
August 18, 2016

Been super busy lately with work, but I did get the chance to make my biceps up. I actually had to try a couple iterations of it to get…

Cosplay & Props Immortan Joe

Vacuum-formed Vambraces

By
on
August 13, 2016

We did the arm armor up, and since we might be offering pulls of the things up for sale to folks who are interested I figured I’d do a very…

Cosplay & Props Immortan Joe

Regal Robes, Refined

By
on
August 11, 2016

The robes got addressed earlier this morning, since I needed them done in order to figure out how the belt will sit over them. The fabric I went with…

Cosplay & Props Immortan Joe

Buckle (swash not included)

By
on
August 10, 2016

If I can share a…

Cosplay & Props Immortan Joe

Holsters and Shin Pads

By
on
August 9, 2016

I glued a supportive piece of foam to the back of the leather with barge cement in…

Cosplay & Props Immortan Joe

Shin(y) and Chrome

By
on
August 5, 2016

Mostly done with one of the shin pads, just playing around with things a bit. I weathered the emblems with some black oil paint diluted in mineral spirits, which…

3D Printing Cosplay & Props Immortan Joe

Automotive Detailing

By
on
August 4, 2016

Most of today was spent getting some of the details on my shin pads done, since I like jumping around between parts of this project like crazy.

The links were…

Cosplay & Props Immortan Joe

Belt adjustments and trimming

By
on
August 1, 2016

I spent a bit of time taking measurements this morning and doing some rough designing of the belt. I think this is about right to fit my close-to-38″ waist,…

Cosplay & Props Immortan Joe

Straps and buckles!

By
on
July 30, 2016

Had a bit of a prototype run with the airbag, and I’m still not happy with it just yet. It’s quite a challenge to figure out ways to sew…

Cosplay & Props Immortan Joe

Clasps and connections

By
on
July 28, 2016

Spent a bit of time refining how the front and back halves of the torso join up and I think I got something workable here.

I…

3D Printing Cosplay & Props Electronics Immortan Joe

Now with working airflow!

By
on
July 27, 2016

This is exciting – it’s actually doing the job! It’ll only get better once everything is properly fitted, but I really need the airbag itself done before I can…

Cosplay & Props Immortan Joe

Swag for a scepter

By
on
July 27, 2016

Two other bits of note for the day. First, I had the opportunity to go back into NYC’s garment district, and this time I went there with the mission…

3D Printing Cosplay & Props Immortan Joe Mold-making and Casting

Printed fittings and pulled forms!

By
on
July 26, 2016

The printed right-angle pipe fitting seems to have worked out pretty well, all things considered!

I need to sand it a bit, glue the parts together, then XTC-3D the whole…